A suitable DC Voltage is applied on each phases of stator winding individually for a fixed time period while recording the current with other two phases grounded. Then, the stator winding is shorted to ground via PDC circuit, and discharge current is monitored as a function of time. The plot of both the charge and discharge current is plotted against time to facilitate comparisons between the two currents.
The Insulation Resistance (IR) values at 1 min interval is accepted as a parameter of significance. Its value determines the state of dryness or wetness of insulation. Also, where the values of IR are lower than 5 MOhm, another parameter i.e. Polarization Index (Ratio of IR 10 min / IR 1 min) is computed and values above 2 are considered acceptable.
The traditional test was determined for Class B thermoplastic insulation that is hygroscopic in nature and wetness of insulation was a major cause of concern. For present day Class F thermosetting type insulation (e.g. Epoxy resin on mica glass fibrous tape) and processes like VPI, moisture penetration is minimal and very high values of IR are obtained. The values do not deteriorate to below acceptable levels specified in IEEE 43, even in highly contaminated machines.
The insulation is modelled as three polarization mechanisms:
Idepol = I0 + a1.e(-t/t1) + a2.e(-t/ t2)+ a3.e(-t/ t3)
The charging curves and discharging curves are plotted over time to get polarization current and depolarization profiling curves.
Two parameters of significance are calculated
Test Equipment: IR Tester: Megger MIT520 and a 100 Ohm Resistor box + Fluke DMM
Several studies have been conducted on leakage currents on surface of glass as well as polymer insulators in normal and polluted conditions. The FFT spectrum of such leakage currents, showed presence of odd harmonics (3, 5, 7, 9 harmonics). The increase in ratio of 3rd/5th harmonic had a strong correlation with increase in leakage current flow in old and contaminated insulators and which increased steely with arcing.
The usage of non-linear dielectric composite materials in stator insulation (epoxy-mica, conductive tape in slot section, semi-conductive stress grading system at slot-exits) and phenomena like contamination on end-winding surface, space charge polarization due to delamination between tape layers, interfacial polarization between layers of composite dielectrics or between the layers of semi-conductive and main insulation, insulation ageing and degradation etc. add to non-linearities and increase in odd/even harmonic content in insulation. At higher voltages, the partial discharges occurring in insulation voids or on overhang surfaces increase the ratio of 3rd/5th harmonic.
Test Equipment: HV Source: DELTA 4110 (Megger-Make) / Power Electronical ILSA Kit: Qualitrol Deltamax-15 or DSO – TBS102B (Tektronix) Shunt: 1 Ohm, Voltage Divider box
The test will be conducted as per CIGRE 552 & IEEE 286: 2000, only on assembled stator windings. The standard is mainly used for testing of stator coils, but for assembled units, it helps to determine the insulation condition or health and is thus an important test. Test shall be for each phase wise (wherever Star point is external) and also for combined phase with respect to ground. Tan delta test shall be done upto rated phase voltage in 5 or more steps from 20% (or 0.5 kV) to 100% rated phase voltage.
Besides the tip-up information which helps in assessing occurrence of partial discharges and effects due to the same, PE goes a step further. We assess the base values and its variation with voltage for both tan delta and capacitance curves and then combine it with the IR profiling, PD test and other test results to determine the state of resin cure, occurrence of de-lamination, ageing/dielectric loss, presence of moisture/contaminants, quality of contact of stress grade system with stator coils.
Test Equipment: HV Source: DELTA 4110 (Megger-Make) or Power Electronical make & Tan Delta Bridge: DELTA 4110 (Megger-Make) or Deltamaxx-15 (Qualitrol make)
The test will be conducted as per the new IEEE 1434: 2000 and IEC 60270, IEC 60034-27.1 & 27.2: 2006, only on stator windings. Test shall be done for each phase (wherever star point is external) and also for combined phase with respect to ground. The PD inception voltage and extinction voltage shall be measured. Online PD will be conducted only if the coupling capacitive sensors are permanently installed at motor terminals and BNC output is providd externally for measurements.
Besides, the PRPD patterns at rated test voltage, PE will provide a set of plots at different test voltages and at different center frequencies that are chosen based on site conditions and patterns obtained, varying from low frequency to high frequency. This gives better insights into actual PD signals and noise elimination, increasing accuracy of the analysis of insulation condition. The report will indicate severity of PD and its location overview with likely cause, which helps in focused maintenance actions.
Test Equipment: HV Source: DELTA 4110 (Megger-Make) / Power Electronical PD Kit: Omicron MPD600 or Qualitrol Deltamax-15 Capacitor: 1000 pF
The test is often recommended for LT motors (but can be applied to HT motors) and follows IEEE 388:1992 and 389:1992 standards. It is also listed in IEEE1415:2006 Guide for Induction Machinery Maintenance Testing and Failure Analysis.
It mainly consists of inductance, capacitance and phase angle checks. Often the LT motors can have interturn fault, it may continue to operate (unlike HT units that will burn immediately causing ground fault). So the test is used mainly as a troubleshooting tool and helps in assessing presence of such faults. The measurements can also used to ascertain cable faults, joints issue, phase unbalance, turn insulation problem.
Test Equipment: All Test Pro 5 from ATPOL
It is also listed in IEEE1415:2006 Guide for Induction Machinery Maintenance Testing and Failure Analysis.
This is not a diagnostic check but mainly used to ascertain balance in three phases. It is often trended to check for any developing high resistive joints etc. This is checked using a micro-ohmmeter which gives better accuracy than a multi-meter given the low values. Test is often important post a rewinding operation but generally no variation is expected for healthy motors. While it is included in Winding Circuit Analysis, this measurement will be cross checked as a micro-ohmeter gives high accuracy for such low resistances.
Test Equipment: Micro-ohmmeter from Prestige or Motwane
The test follows IEEE 522 standard.
The main aim of the test is to assess health of inter-turn insulation which is not obtained in a Megger test. A repetitive voltage surge of known voltage level (corresponding to rise time and motor rated voltage is applied at motor terminals and its damped characteristic is measured and compared for different phases. Any mismatch indicates shorted turns. The test also gives a developing interturn indication and is effective than inductance/impedance measurements.
Test Equipment: Surge Tester – Jabbals